Making the Vindonissa Gallic F - Printable Version +- RomanArmyTalk (https://www.romanarmytalk.com/rat) +-- Forum: Reenactment (https://www.romanarmytalk.com/rat/forumdisplay.php?fid=5) +--- Forum: Roman Re-Enactment & Reconstruction (https://www.romanarmytalk.com/rat/forumdisplay.php?fid=26) +--- Thread: Making the Vindonissa Gallic F (/showthread.php?tid=16520) |
Making the Vindonissa Gallic F - L_CORNELIUS_CETHEGUS - 03-01-2010 Hi all, I've started a reconstruction of the Vindonissa Gallic F ([url:xxg7eh4r]http://www.romanarmy.com/cms/component/option,com_helmets/task,view/cid,60/Itemid,96/[/url]). I wanted to do one of the Fs and preferably one that hasn't been paid a lot of attention to... Since there have already been some excellent conversations on the other Fs in the database, but not that much focus on the Vindonissa, I would really appreciate any comments on the bowl I have so far, and the neck guard and cheek guards I'll be making next. Here's where I am so far... [attachment=3:xxg7eh4r]<!-- ia3 DSC_0010.JPG<!-- ia3 [/attachment:xxg7eh4r] [attachment=2:xxg7eh4r]<!-- ia2 DSC_0013.JPG<!-- ia2 [/attachment:xxg7eh4r] [attachment=1:xxg7eh4r]<!-- ia1 DSC_0014.JPG<!-- ia1 [/attachment:xxg7eh4r] [attachment=0:xxg7eh4r]<!-- ia0 match-photo.JPG<!-- ia0 [/attachment:xxg7eh4r] From what I've read here on RAT I may need to shorten the occipital area by about 30% but I was trying to leave a little extra until I could compare with the photos in the database. Also, maybe the brow needs to come down a tad (maybe I can cover any messy areas with the silvered brow band). The marker is for approximate placement, and I'll fine tune it a bit more once I get the neck guard on. Thanks, Kelsey Re: Making the Vindonissa Gallic F - L_CORNELIUS_CETHEGUS - 03-02-2010 Here's what the neck guard looks like with the measurements I've calculated from the database (about 1.25"/32mm on each side and 2.25/57mm at the bottom). I thought the measurements looked on the small side, comparing to the other Gallic Fs such as the Besancon. [attachment=1:37rsiygm]<!-- ia1 Library - 158.jpg<!-- ia1 [/attachment:37rsiygm] [attachment=0:37rsiygm]<!-- ia0 Library - 159.jpg<!-- ia0 [/attachment:37rsiygm] --Kelsey Re: Making the Vindonissa Gallic F - Peroni - 03-02-2010 Looking good Kelsey! Look forward to seeing the finished article! Re: Making the Vindonissa Gallic F - jvrjenivs - 03-02-2010 How did you make the bowl. I get the impression it is made by 2 halves welded together, but I'm not sure? Anyway, a very nice project and good luck with finishing this piece. Re: Making the Vindonissa Gallic F - L_CORNELIUS_CETHEGUS - 03-02-2010 Quote:How did you make the bowl. I get the impression it is made by 2 halves welded together, but I'm not sure? Anyway, a very nice project and good luck with finishing this piece. No welding yet... I started with a civil defense helmet, then brought the back brim of it down flat using an oxygen/propane torch and a mushroom stake on the anvil. Here are a couple pictures to give you a better idea [attachment=1:l80sum2x]<!-- ia1 DSC_0001.JPG<!-- ia1 [/attachment:l80sum2x] [attachment=0:l80sum2x]<!-- ia0 DSC_0003.JPG<!-- ia0 [/attachment:l80sum2x] --Kelsey Re: Making the Vindonissa Gallic F - Gaius Julius Caesar - 03-02-2010 Now thats crafty lol Those holes around the brim had me wondering about their purpose.... Re: Making the Vindonissa Gallic F - Uhrisa - 03-04-2010 Very interesting project. What are the inner dimensions of the helmet? Regards Re: Making the Vindonissa Gallic F - L_CORNELIUS_CETHEGUS - 03-04-2010 Quote:What are the inner dimensions of the helmet? The interior dimensions of the original were documented by Martin Hoffman in "Ein Helm vom Typ Weisenau aus Vindonissa" (many thanks to Jens Horstkotte for sending it to me) as 23cm long (~9") and 20.3cm wide (~8"). The interior dimensions of the bowl I have right now is 9-1/4" long (23.5cm) and 8-1/8" wide (20.6cm). Pretty close. I haven't measured the interior height yet. --Kelsey Re: Making the Vindonissa Gallic F - Uhrisa - 03-05-2010 Ah, thanks for the information! I'm looking forward to see the progress in your project! Good luck! Regards Re: Making the Vindonissa Gallic F - L_CORNELIUS_CETHEGUS - 03-07-2010 Update... I have most of the metal work done... almost ready to do the brass. Here are some pictures of the work so far. [attachment=2:1mr4p800]<!-- ia2 Gallic Helmet - 38.jpg<!-- ia2 [/attachment:1mr4p800] [attachment=1:1mr4p800]<!-- ia1 Gallic Helmet - 40.jpg<!-- ia1 [/attachment:1mr4p800] [attachment=0:1mr4p800]<!-- ia0 Gallic Helmet - 42.jpg<!-- ia0 [/attachment:1mr4p800] --Kelsey Re: Making the Vindonissa Gallic F - M. Demetrius - 03-07-2010 ...then you used the other part of the brim to make the neck guard, and welded the two together? Clever. Now the big question is, where did the Romans get all those Civil Defense Helmets to start their helmets?? :wink: Very innovative work. I'll bet it took quite a few heats to get the rows of "bumps" on the back of the helmet, eh? Re: Making the Vindonissa Gallic F - L_CORNELIUS_CETHEGUS - 03-07-2010 Quote:...then you used the other part of the brim to make the neck guard, and welded the two together? Clever. Actually, I had some scrap 18 gauge steel sitting around so I just tossed the brim that I cut away. And yes, lots and lots of heat to get the ridges on the occipital area. 18 gauge cools down so quick you can only work on about a 1/2 inch at a time. As long as its red hot, it doesn't take any force... just lots of patience. ...speaking of those ridges, I've read some conversations here about the shape of them on the Gallic Fs. On the others I think they mostly come to a pointed crest. Some opinions on the Vindonissa is that they are round. It's hard to tell from the photos, so I made them round-ish. Here's a closeup. [attachment=0:3v0os0rj]<!-- ia0 Gallic Helmet - 44.jpg<!-- ia0 [/attachment:3v0os0rj] --Kelsey Re: Making the Vindonissa Gallic F - jvrjenivs - 03-07-2010 very nice. Good luck with the brass edging. Just did that part of my new helmet, and some areas were rather difficult. Re: Making the Vindonissa Gallic F - L_CORNELIUS_CETHEGUS - 03-17-2010 Pretty much done! Here are some pictures of the finished product [attachment=5:2stsmayh]<!-- ia5 Gallic Helmet - 49.jpg<!-- ia5 [/attachment:2stsmayh] [attachment=4:2stsmayh]<!-- ia4 Gallic Helmet - 54.jpg<!-- ia4 [/attachment:2stsmayh] [attachment=3:2stsmayh]<!-- ia3 Gallic Helmet - 52.jpg<!-- ia3 [/attachment:2stsmayh] [attachment=2:2stsmayh]<!-- ia2 Gallic Helmet - 53.jpg<!-- ia2 [/attachment:2stsmayh] [attachment=1:2stsmayh]<!-- ia1 Gallic Helmet - 50.jpg<!-- ia1 [/attachment:2stsmayh] Honestly there's a little bit more planishing I intend to do around the brows but I need to make a trip to the metal yard to fix myself up with a decent ball stake. Still have to do the liner, crest holder, crest, etc. Other than that, I'm fairly pleased with the results. All questions or comments are welcome. BTW here's a slightly better picture of the original, which I've used a lot as a reference point. All the measurements I have are pretty close to those reported by Hartmann in his report on the finding. I think there is some belief that this helmet belonged to an immunis because the helmet was found in a cubiculum that was larger than the standard legionary cubiculum. Interesting stuff! [attachment=0:2stsmayh]<!-- ia0 Gallic Helmet - 25.jpg<!-- ia0 [/attachment:2stsmayh] Re: Making the Vindonissa Gallic F - jvrjenivs - 03-17-2010 wonderful. I certainly like your helmet. Just a question. How did you do the cups for the enamel? Just like you did it on you pugio, but with brass nails instead? And, whats next? |