Posts: 65
Threads: 5
Joined: Aug 2006
Reputation:
0
I actually just got a propane torch a week or so ago, to finish up bending my hinges and such, and just tried it a couple of days ago; on the ones that I tried it with, I was extremely satisfied with the results
Brandon Shifflet
Posts: 2,253
Threads: 31
Joined: Jan 2001
Reputation:
0
You can get little cakes of beeswax at a fabric store--it is used for waxing thread while hand-sewing. (Sometimes come with little plastic holder, not really necessary!) Leather supply places will have it, too. Or you can buy a big brick of it at craft stores like JoAnns, Michaels, etc.
The Legio XX pattern pages should all include a scale of inches. Just enlarge until they match your ruler. 136 percent sounds like it should be in the ballpark. One thing to remember is always aim for the thin wispy look--it's very easy to cut the patterns out OUTside the lines, trace them onto the brass, cut outside THOSE lines, and when you're done your hinges are huge and blobby. The originals are small and elegant, usually. I really ought to re-do those patterns some day!
Matthew
Matthew Amt (Quintus)
Legio XX, USA
<a class="postlink" href="http://www.larp.com/legioxx/">http://www.larp.com/legioxx/
Posts: 1,568
Threads: 207
Joined: Jul 2001
Reputation:
0
Annealing brass for most fittings.... we stopped. It certainly makes it easier to bend and shape and cut the brass but it also weakens it. We'll anneal brass rod to shape torso closure fittings, but the rehammering usually rehardens it to a certain extent.
The trick to quick, clean chisel cutting is a sharp chisel and the right surface to hammer into... we prefer a lead block. This eliminates the need to aneal.
Matt's correct about the seeming delicate shape of lobate hinges . We offer our guys 12 hinge patterns some of which are down right gnarly and chunky. We also enourage the occasional use of some of the repair hinges that have been found.
Hibernicus
LEGIO IX HISPANA, USA
You cannot dig ditches in a toga!
[url:194jujcw]http://www.legio-ix-hispana.org[/url]
A nationwide club with chapters across N America
Posts: 65
Threads: 5
Joined: Aug 2006
Reputation:
0
Thank you Matt, and Hibernicus. Matt, for one, I would be incredibly grateful if you were to P
Brandon Shifflet
Posts: 13,279
Threads: 102
Joined: May 2006
Reputation:
3
So working brass rehardens it? Is it the same for bronze? I bought a torch too, so I can start some little projects. If the weather ever clears up! :x
Visne partem mei capere? Comminus agamus! * Me semper rogo, Quid faceret Iulius Caesar? * Confidence is a good thing! Overconfidence is too much of a good thing.
[b]Legio XIIII GMV. (Q. Magivs)RMRS Remember Atuatuca! Vengence will be ours!
Titus Flavius Germanus
Batavian Coh I
Byron Angel
Posts: 152
Threads: 15
Joined: May 2007
Reputation:
0
Getting back to the original point;
I purchased a jewlery saw and I'm quite happy with it. I recently cut the triangular piercings for a Strilfield Seg (all 16) out of 1mm brass (fully rolled) in other words 2mm. Considerably thicker than original but it's a special for a gorilla.
I did go though about 12+ blades, but you get loads for next to nothing.
The two important things I found were;
1. mount the blade squarely in the end grips then put on plenty of tension using the top adjuster.
2. let the saw do the work, don't push. It takes ages, but it will work.
Mark Downes/Mummius
Cent Gittus, COH X. LEG XX. VV. Deva Victrix
____________________________________________
"Don\'\'\'\'t threaten me with a dead fish!" - Withnail
Posts: 65
Threads: 5
Joined: Aug 2006
Reputation:
0
Thank you, Marcus. What's a Strilfield? I can't seem to find anything on the internets about it. You know what they say about inquiring minds
And yes, Giaus, from what I can understand, heating brass up to red-hot, then letting it cool softens the brass, whereas working it with a hammer makes it harder. Again, that's just my understanding, but I think that's how it goes.
Brandon Shifflet
Posts: 1,677
Threads: 75
Joined: Nov 2005
Reputation:
5
Posts: 65
Threads: 5
Joined: Aug 2006
Reputation:
0
Thanks Martin, but I actually have both of those links bookmarked to my favorites; I have quite a collection of references for any little thing
Brandon Shifflet
Posts: 152
Threads: 15
Joined: May 2007
Reputation:
0
Brandon,
A Strilfield is just the updated Newstead Pattern.
Check out Matt Amt's , VI Victrix or Jared's site (Florentius).
Mark Downes/Mummius
Cent Gittus, COH X. LEG XX. VV. Deva Victrix
____________________________________________
"Don\'\'\'\'t threaten me with a dead fish!" - Withnail
Posts: 65
Threads: 5
Joined: Aug 2006
Reputation:
0
Ah, very nice. Quite pretty
Brandon Shifflet
Posts: 1,962
Threads: 106
Joined: Apr 2003
Reputation:
7
Put some wax or gun/ machine oil in the saw, and it goes a lot more fast and brokes a lot less.
Posts: 65
Threads: 5
Joined: Aug 2006
Reputation:
0
Okay, according to my measurements of the Legio XX blueprints for hinges, they should be about 2,3/4" x 1,1/8" at the barrel; is this correct? Sorry, it's just kinda part of my own "measure twice (more like 6 times :wink: ) and cutting once"
Brandon Shifflet
Posts: 65
Threads: 5
Joined: Aug 2006
Reputation:
0
anyone? anyone wanna measure their hinges real quick? It'd be extremely helpful
Brandon Shifflet
Posts: 1,677
Threads: 75
Joined: Nov 2005
Reputation:
5
Quote:anyone? anyone wanna measure their hinges real quick?
Mine are made after an original find, starting from a 28x65 mm rectangle. I posted pictures of those hinges here
|